[sogone]

How did everyone do their accelerator cables? Or what did you use. The stuff I have supplied just doesn't work out. Pj, supplied what he thought was a baleno accelerator but it just fit. Any ideas on what I can use to make this all work.

[slowsierra]

i used the standard cable and modified the sierra accel pedal

greg

[steak_knife]

efi Vit cable....

[sogone]

Even with the baleno throttle being completely different?

[steak_knife]

Pic.........

tis in a different spot, but don't think it's that different that it won't fit/work

[sogone]

I tried changing the bracket round to make it work however it was then too long for the the adjustment nuts.




And the supplied cable

[BlueSuzy]

slowsierra wrote:

i used the standard cable and modified the sierra accel pedal

greg

x2

If anything it was too long, Mine was down the back of the motor, Then up to the TB

[steak_knife]

That look's like a vit cable, try as the others have said....

[sogone]

Ok back to this.

Can someone measure their Efi vit cable from ball bearing thingy to ball bearing thingy.

The standard cable I have will not fit at all. Even Joel's brand new cable I borrowed from him for a g13ba will not fit.

[BlueSuzy]

The baleno cable is straight at the throttle body side

[tanshi]

I used a vit one i think, but shortened the inner using a brake cable end from a push bike shop.

[sogone]

BlueSuzy wrote:

The baleno cable is straight at the throttle body side

I don't have the stock baleno cable. Just the one supplied by pj.zook and one I pinched from Joel. Both identical. I'm not running a body life which probably answers why over all it too short. But it still itsnt long enough from the bracket to the throttle body



Have you got a picture with what you mean tanshi?

[sogone]

Problem fixed. Probably not 'legal' in a sense but alot better IMO then dodging it with cable ties and what not.

Used go kart cable joiner crimp joiner ma-bobby thingys. Got a pack of 5 for $6 or something. Cut the cables to length with slack spare on each side. Installed it then tightened it proper job when it was how I wanted it. Works a dream.



Tidied it up after so no loose ends.


Doesn't snag on anything and sits in the baleno stock accelerator holder bracket thing.

[BlueSuzy]

That will probably work fine. There is not much tension on throttle cables.

[joel]

not sure of legalities, but i doubt it would be a problem??
looks the goods, not like its a dodged break cable.....

[sogone]

I owe ya a new cable. Used yours in the end as well cause I cut mine too short

[CairnsZook]

I used the standard Baleno cable. Just had to mod the pedal end slightly to fit.

[sogone]

I didn't have the stock cable handy. Just had a g13ba one and a corolla 4k one. Made it flash as for $6. New baleno cable was gonna set me back $30 or something.

[Brenno]

I used a jimny cable when I put my jimny motor in, same manifold design.

[BlueSuzy]

Brenno wrote:

I used a jimny cable when I put my jimny motor in, same manifold design.

How was the pedal?

Um, I can look at my Jimny tomorrow..

[Brenno]

I used a jimny cable when I put my jimny motor in, same manifold design.

[sogone]

Thanks brenno. Good advice

[Brenno]

Just needed a small nut and bolt to squash the end in the pedal,

[steak_knife]

Simply because of the title, I'm going to put this here.....

http://www.ptjau.com/images/sierra/bale ... ringv1.pdf

[steak_knife]

Oh, thanks to P.J.Zook....