| Author |
Message |
outram
Joined: Mon Aug 30, 2010 9:51 am Posts: 130 Location: newcastle
Vehicle: suzuki sierra sj80
|
 Posted: Tue Apr 07, 2015 5:45 pm |
|
|
Hey guys how hard is it to remove cv joint then split the cv to be able to remove and install new boot on a suzuki vitara
|
|
|
|
 |
christover1

az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
 Posted: Tue Apr 07, 2015 6:26 pm |
|
|
There are boots available to fit around without pulling them out, ask at auto shops. But I have never tried them, so no idea how good they are.
Passenger side is easy to remove, but drivers can be a bitch, lots of disassembling to slide the inner cv out of diff.
Theres circlip on outer end of outer cv behind the free wheel hub. And 3 bolts on inner for passenger side. And drivers side slides into diff.
|
|
|
|
 |
outram
Joined: Mon Aug 30, 2010 9:51 am Posts: 130 Location: newcastle
Vehicle: suzuki sierra sj80
|
 Posted: Tue Apr 07, 2015 7:33 pm |
|
|
Ok buddie thank you thinking i might just replace it has alot of grit in the grease
|
|
|
|
 |
Zoro

az supporter
Joined: Mon Jan 26, 2015 7:03 am Posts: 33
Vehicle: '89 Suzuki Vitara
|
 Posted: Thu Apr 09, 2015 12:16 pm |
|
|
I had to do mine to get a RWC. Wasn't too difficult. I took the whole passenger side apart, but I also needed to do the A arm bushes, so if it was just the boot, just drop the shaft out, take it apart and change the boot.
I'd recommend doing both ends (inner and outer) while you have it apart, a boot is like $15, may as well change both while you're there.
|
|
|
|
 |
outram
Joined: Mon Aug 30, 2010 9:51 am Posts: 130 Location: newcastle
Vehicle: suzuki sierra sj80
|
 Posted: Thu Apr 09, 2015 4:09 pm |
|
|
The outter side how do u split the joint inner seams to pull apart the outter is fixed
|
|
|
|
 |
christover1

az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
 Posted: Thu Apr 09, 2015 5:15 pm |
|
|
Internal locking ring springycirclip thing hiding in the grease
|
|
|
|
 |
outram
Joined: Mon Aug 30, 2010 9:51 am Posts: 130 Location: newcastle
Vehicle: suzuki sierra sj80
|
 Posted: Fri Apr 10, 2015 10:16 am |
|
|
So u have too knock it off with a dolly ??
|
|
|
|
 |
christover1

az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
 Posted: Fri Apr 10, 2015 12:27 pm |
|
|
No, circlip pliers and/or 2 screw drivers to hook it out, on mine anyway, guess there could be different types.
|
|
|
|
 |
AckerDackerly

az supporter
Joined: Thu Jun 02, 2011 9:53 pm Posts: 361 Location: Independence, MO USA
Vehicle: 1993 RHD Suzuki Escudo Tintop
|
 Posted: Fri Apr 10, 2015 2:20 pm |
|
Here is a document I put together after dealing with Boot damage on a SWB '96 Tracker (Vitara) I once owned: http://acksfaq.com/cvhalfshaft.htmThe short side axle shaft is a pain to remove. I went ahead and removed both the strut bolts and the A-arm ball joint in order to remove the shaft for "re-booting". In retrospect, I could have done it with only the strut bolts removed. Since I had the unit apart, I completely cleaned out the old grease and then reapplied new grease to the joint before installing the new boot. Split boots are, in my opinion, a waste of money. Zip (sometimes called "baker") ties work only in an emergency as they degrade with exposure to the elements. Use the steel bands that come with the boots. I hope that this helps!
_________________ -Ack http://www.acksfaq.com88, 88.5 SJ413
|
|
|
|
 |
outram
Joined: Mon Aug 30, 2010 9:51 am Posts: 130 Location: newcastle
Vehicle: suzuki sierra sj80
|
 Posted: Fri Apr 10, 2015 6:28 pm |
|
|
Cheers guys found a crack in my old cv so ordered a new one
|
|
|
|
 |
|